Home > Support > Knowledge Base
Knowledge Base
 
Reset Search
Search
 

 

Knowledge

Rabbit: Critical Serial Flash Patch

« Go Back

Information

 
Article Number000005246
Problem Resolution
********************************************************************************
   Patch Notes for Serial Flash Support Update                      19-May-2015
********************************************************************************

   *** 24-Nov-2015 Updated to include RCM4310 and BL4S200. Both of these
   products require a recomple with a patched version of Dynamic C.

   Effective May 2015, several Rabbit brand boards are impacted by a serial 
   flash end of life. For the boards in the table shown below, the replacement 
   serial flash part requires applications to be recompiled with a patched 
   version of Dynamic C. The table below shows the boards impacted, the first
   board revision impacted, and the required patch version of Dynamic C.
   
   | Rabbit Product |     Part No | Rev+ | Patch Part #   | Software Version |
   |----------------+-------------+------+----------------+------------------|
   | RCM6700        | 20-101-1318 | G    | 40002882_B.zip | Dynamic C 10.72  |
   | RCM6710        | 20-101-1319 | G    |                |                  |
   | RCM6750        | 20-101-1320 | H    |                |                  |
   | RCM6760        | 20-101-1321 | H    |                |                  |
   | RCM6600W       | 20-101-1322 | F    |                |                  |
   | RCM6650W       | 20-101-1323 | F    |                |                  |
   | RCM4200        | 20-101-1131 | G    |                |                  |
   | RCM4210        | 20-101-1132 | G    |                |                  |
   | RCM4310        | 20-101-1139 | L    |                |                  |
   | RCM5400W       | 20-101-1246 | K    |                |                  |
   | BL5S220        | 20-101-1260 | H    |                |                  |
   | BL4S110        | 20-101-1256 | G    |                |                  |
   | BL4S200        | 20-101-1220 | J    |                |                  |
   |----------------+-------------+------+----------------+------------------|
   | RCM3305        | 20-101-1067 | E    | 40002882_B.zip | Dynamic C 9.62   |
   | RCM3315        | 20-101-1068 | E    |                |                  |
   | RCM3319        | 20-101-1195 | G    |                |                  |
   | RCM3700        | 20-101-1305 | C    |                |                  |
   | RCM3710        | 20-101-1328 | C    |                |                  |
   | RCM3720        | 20-101-1329 | C    |                |                  |

   Installation

   Unzip the archive to a location on your hard drive. The patch is structured
   by Dynamic C version and as an overlay to your existing installation. 
   To use the patch, simply copy the patch over your existing version of 
   Dynamic C to replace your existing files with the patched versions of the 
   same.

   Recompililation Required

   Recompilation of your existing application is required for all affected
   products listed in the table above. In other words, if your product's part 
   number is at the revision listed or a later revision, then you will need to
   build a new binary image with the patched version of Dynamic C. Note that
   the binary image will work with both new revision and older revisions of the
   products.

   Previous Versions of Dynamic C

   Customers using previous versions of Dynamic C must upgrade to the 
   version listed in the table above in order to use the patch.

Patch available on the Dynamic C page on Digi's website:
Dynamic C 9.62/10.72 Adesto Patch

********************************************************************************

Feedback

 

Was this article helpful?


   

Feedback

Please tell us how we can make this article more useful.

Characters Remaining: 255